There are many times you wish to a specific device of your own to reduce volumes or any measurements of your concern. An example could be your audio equipment, deflections in a cantilevered stairway, or even the noisy tachometer of your motorbikes. For these adjustments, you may opt to use a potentiometer which is a variable resistor.
In some cases, devices which involve circuitry and an equation are produced as an aid to these situations. Known as the most fundamental circuit, this tool is called a Voltage Divider. It is a passive circuit which helps reduce the large volumes of your audio equipment or other electronics.
Using two resistors, this divider shall allow you to turn a large voltage into a smaller one provided that you also have the value of input voltage. Understand how this device works need you to be familiar with the Ohms law which states, the direct current flowing in a conductor is directly proportional to the potential difference between its ends.
A circuit where the Volt runs through is one of the essential parts of this tool. The other is called an equation where you should find the Vout by taking the ratio between two resistors. These two parts are vital in reducing your volt counts and in the absence of either one of its variables, the procedure will never take effect.
Though you can buy your own device, creating a portable one can be a better choice as it helps you save. For this, you have to secure leads, resistors, a 9V battery, alligator clamps, voltmeter and its connectors. In addition, you have to ensure that you get at most the standard battery voltage which is 9.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Make sure that you have provided a solid twist for it by clamping an alligator clamp on it. Then look at the positive and negative terminals of the battery. When found, attach the red wire to the positive and the black wire to the negative. Then turn your meter on.
As you can see from 9V, your voltage goes down to 3V. When this happens, the positive terminal of the circuit is now the one where the twist is located. Meanwhile, the negative terminal is retained as the negative source.
When doing this procedure, always see to it that you have unhooked an end of a divider or unplugged your battery to prevent it from draining. More so, be cautious when working with these types of wiring especially the ones which are still plugged into its outlet because it may result in electrocution. In this case, however, there is not much danger in a 9V energy source.
In some cases, devices which involve circuitry and an equation are produced as an aid to these situations. Known as the most fundamental circuit, this tool is called a Voltage Divider. It is a passive circuit which helps reduce the large volumes of your audio equipment or other electronics.
Using two resistors, this divider shall allow you to turn a large voltage into a smaller one provided that you also have the value of input voltage. Understand how this device works need you to be familiar with the Ohms law which states, the direct current flowing in a conductor is directly proportional to the potential difference between its ends.
A circuit where the Volt runs through is one of the essential parts of this tool. The other is called an equation where you should find the Vout by taking the ratio between two resistors. These two parts are vital in reducing your volt counts and in the absence of either one of its variables, the procedure will never take effect.
Though you can buy your own device, creating a portable one can be a better choice as it helps you save. For this, you have to secure leads, resistors, a 9V battery, alligator clamps, voltmeter and its connectors. In addition, you have to ensure that you get at most the standard battery voltage which is 9.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Make sure that you have provided a solid twist for it by clamping an alligator clamp on it. Then look at the positive and negative terminals of the battery. When found, attach the red wire to the positive and the black wire to the negative. Then turn your meter on.
As you can see from 9V, your voltage goes down to 3V. When this happens, the positive terminal of the circuit is now the one where the twist is located. Meanwhile, the negative terminal is retained as the negative source.
When doing this procedure, always see to it that you have unhooked an end of a divider or unplugged your battery to prevent it from draining. More so, be cautious when working with these types of wiring especially the ones which are still plugged into its outlet because it may result in electrocution. In this case, however, there is not much danger in a 9V energy source.
About the Author:
When you are searching for the facts about a voltage divider, come to our web pages. More details are available at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment